Point Haircutting Technique Guide

Point cutting is one of the cutting techniques that differentiates a boring haircut from an exciting one.

Point hair cutting is used for texturizing the hair and removing bulky strands at the edges. This creates different layers that blend beautifully and make your hair look great.

Point cutting can be used for male or female hair styling. Point cutting can be used for both wet or dry hair, depending on the texture and thickness of the hair. It can also help to fix any hairstyle that isn't quite right.

How do you use the point-cutting technique?

To learn how to cut hair, you need both skills and tools. You will need tools for point cutting and similar styles. These tools include:

• A comb
• You can use 6.5-inch shears for barbering, or any other size that you are comfortable with and gives you the most control.
• A good chair
• Mirror

First, you need to cut the hair in sections starting at the scalp. Slowly comb a section of hair, and then hold it vertically with your fingertips at 6cm from its tip.

You should leave enough space between your fingers, the tips of the hair, and the rest of the hair for this technique to work. You should also ensure that the hair is not too close to the tips. This will prevent it from falling over and making it difficult to texturize.

Once you have your hair in the right position, the other hand can be used to grab your scissors, clipper or shears. You should hold it straight in the direction you want to cut the hair.

When using your scissors to trim hair, you should remember that the goal is to texturize the tips and not reduce its length. You are not supposed to cut off large amounts of hair.

You may lose more hair if you position your scissors at an angle to the hair.

Once you are done with one area of hair, go to the next section and comb the hair again until you have the desired texture. Point cutting, unlike other hair texturizing methods, takes a lot of time because you have to make subtle cuts in very small areas.

1.Keep the scissors at 45 degrees.

To create a more dense texture, hold the handle end of your scissors down. To achieve a more layered and choppy look with your hair, do not lower the scissors below 45 degrees.

2.Make a cut of at least 1 inch

After you've pounded the hair between your fingers (as described in the paragraphs above), don't cut it any deeper than one inch. If you desire to achieve a dramatic effect, a point-cut should cut off 1 inch of hair. However, you can go as deep as 1 to 2 inches. This technique should not exceed 5 cm (5 inches) in length.

It is crucial to inform the client of the amount of hair that you are cutting before you begin.

3. Remove the bottom layer of hair

Take a small portion of your hair and hold it between your fingers, about 2 inches above the tip. Let the hair hang down, instead of pulling it up like you would for shorter hair. Next, use your scissors to begin cutting upwards.

This is done to prevent the hair from looking straight.

Tips & Tricks For Point Haircutting

• Point cutting is a slow and patient method that cuts small sections of hair. It is a time-consuming process. You may feel tempted to cut faster or with a larger section, but this is not the best option. It is best to take it slow and cut small amounts of hair at once.
• Be careful when using scissors. Place your scissors parallel to the tips of the hair. Avoid putting it too deep into the hair. This could lead to you cutting your hair too deeply or risk damaging the hair. Point cutting is best done slowly, steadily, and carefully.
• Professional cutting shears, razors, and clippers are also available. To get a better cut, use sheers with long blades.

How To Use Point Haircutting Techniques on Short and Medium Length Hair

1. Comb your hair.

Wash your hair thoroughly. To remove any tangles and loosen hair, you should comb your hair.

Dry and straighten your hair after you have finished coiled or textured hair.

2. Take a small section measuring approximately 5 cm (2 inches).

Use your non-dominant arm to comb 2 inches (5 cm) vertically. As the hair is still in your comb, hold the hair between your middle and forefinger.

Start working in a circular motion with the scissors.

You should not hold your hair longer than 2 inches at once. This can cause your hair to flop and make it difficult to achieve a smooth texture. Working with less than 2 inches may not give you the best texture.

3. Position the hair scissors downwards

Point cutting is different from normal cuts which require you to hold the scissors straight up. Instead, you need to keep the scissors at the same axis with your finger.

Point cutting does not reduce length, but removes bulk and creates a beautiful texture. You must move your scissors in a zigzag fashion.

4. You can start removing large chunks of hair

Use your scissors to cut about 1 inch (22.5 cm) of hair. Take another cut by moving the scissors to 0.3cm. Continue moving the scissors down the hairline, making the same moves with each move. You should have created valleys or peaks in your hair when you are done.

To avoid looking ragged, keep the length of your hair at a standard point.

5. Reduce from down to up

Start at the nape of your neck and work your way up the sides. Next, you will move on to the crown and the top. 

When should you avoid using the point haircutting technique?

Point cutting is a great idea for family and friends, but sometimes it doesn't work. These are not the best situations for point cutting.

• If the hair of the subject is already very thin
• If the client desires a sleek, almost minimalistic hairstyle
• If you're not an expert stylist, don't trim your hair at first.

Point cutting can give your hair texture and flavor, but it should not be used as a general technique. These are some of the reasons why point cutting is not recommended. If the client has very long hair or is permed or very wavy, point cutting should be avoided. It is crucial to evaluate the situation before you add texture.

Conclusion: what you need to know about point haircutting techniques

These tools do not suffice. Patience is also important. Point-cutting can cause you to lose patience. You might lose patience if you don't have patience. This could cause the trim to be ineffective. You will need to be seated in a comfortable chair so that your hair does not move during the trim.

Point cutting can be done in two ways. Either let your hair hang naturally, or you can pull your hair up between your middle finger and the tips of your fingers. Holding your hair can help you see how much you've cut. If you allow your hair to hang, you can make sure you don't cut more.

Your hair shouldn't look curled. Instead, use a comb to measure your hair and draw a straight line. This is the most basic method to trim hair in a salon. The tip of a scissors can be used to quickly trim hair. You shouldn't go too deep into the hair. They should look lighter, but not necessarily shorter.

Trim as much hair as possible with each pass. When you're done, take a step back and drop the section. Next, take a look at the hair again and start over. When the ends look natural, you are done.

If you're cutting your own hair, you can finish it in the mirror. The client can view the finished product and hear their comments. The client can then see the final product and give feedback.

The perfect hairstyle doesn't require you to be very thick. Before you cut your hair, however, it is important to know how to properly point your hair. A quick trim can add visual interest to your hair, reduce weight, and conceal an obvious line. Take care when you cut your hair.